Tabelka poniżej prezentuje parametry techniczne urządzenia. W przypadku, gdyby prezentowane w niej informacje były niekompletne lub budziły wątpliwości prosimy o kontakt mailem bądź telefonicznie z naszym działem technicznym. Dodatkowo służymy pomocą w doborze właściwego urządzenia tak, aby optymalnie spełniało wymagania Państwa projektu.
Product specification
Output
DC Voltage Range
48 V
Rated Current
0.85 A
Current Range
0 ~ 0.85 A
Ripple and Noise (max.)
180 mVp-p
Rated Power
40.8 W
Voltage Adj. Range
43.2 ~ 52.8 V
Voltage Tolerance
+/- 1%
Line Regulation
+/- 1%
Load Regulation
+/- 1%
Setup, Rise Time
less than 800ms, less than 50ms/230Vac at full load
Hold Up Time (Typ.)
> 32ms / 230VAC >16ms / 115VAC at full load
Input
Voltage Range
88 V ~ 264 VAC 124 ~370 VDC
Frequency Range
47 Hz ~63 Hz
Efficiency (Typ.)
84 %
AC Current (Typ.)
0.8 A / 115VAC 0.4A / 230VAC
Inrush Current (Typ.)
COLD START 30A / 115VAC 60A / 230VAC
Leakage Current
< 1mA / 230VAC
Protection
Over Load
> 105 % rated output power
Protection type : constant current limiting, automatically after fault condition is removed
Over Voltage
115% ~ 150% rated output voltage
Protection type : latch-off mode
Environment
Working Temp.
-20C ~ 70C (Refer to output load de-rating curve)
Working Humidity
20 ~ 90% RH non-condensing
Storage Temp., Humidity
-40 ~ +85C, 10 ~95% R.H
Temp.Coefficient
+/- 0.03%/C (0 ~ 50C)
Vibration
10 ~ 500Hz, 2G 10min./1 cycle, period for 60 min. Each along X,Y,Z axes
Safety and EMC
Safety Standards
UL508, TUV EN60950-1 : 2006+A11, UL1310 NEC class 2 compliant
Withstand Voltage
I/P - O/P : 4242 DC I/P - FG : 2121 DC 1 minute
Isolation Resistance
I/P - O/P, I/P - FG, O/P - FG: 100M Ohm / 500VDC
EMI Conduction and Radiation
EN55022 : 2006 Class B
Harmonic Current
EN61000-3-2: 2006 Class A, EN61000-3-3: 1995+A1: 2001+A2: 2005
EMS Immunity
EN61204-3: 2000, EN55024:1998+A1: 2001+A2: 2003 light industry level, criteria A
Others
Colling
Free Air convection
Packing
0.28kg ; 27Pcs / 8.76kg
DC OK signal
Relay contact (30VDC / 1A , 120VAC / 1A)
Connection
I/P 3 poles, O/P : 6 poles screw DIN termina
Dimension (W*H*D)(mm)
40x90x99
MTBF (MIL-HDBK-217F)
562.7K HR
All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25°C of ambient temperature.
Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47 uf parallel
capacitor.
Tolerance: includes set up tolerance, line regulation and load regulation.
De-rating may be needed under low input voltages. Please check the de-rating curve for more details.
The power supply is considered a component which will be installed into a final equipment. The final equipment must be
re-confirmed that it still meets EMC directives.
Selection Guide
