Kompaktowy programowalny sterownik automatyki umożliwiający komunikacje po Ethernecie, RS-232 i RS-485. Ffirma ICPDAS, zapewnia oprogramowanie "development tool kits" (Xserver, VxComm, biblioteki Modbus). Dzięki niemu użytkownicy mogą bez problemu dostosować urządzenia z portami szeregowymi do podłączenia do sieci Ethernet lub poprzez protokół Modbus do komunikacji z oprogramowaniem SCADA.
Tabelka poniżej prezentuje parametry techniczne urządzenia. W przypadku, gdyby prezentowane w niej informacje były niekompletne lub budziły wątpliwości prosimy o kontakt mailem bądź telefonicznie z naszym działem technicznym. Dodatkowo służymy pomocą w doborze właściwego urządzenia tak, aby optymalnie spełniało wymagania Państwa projektu.
Specification
Models
μPAC-7186EG
μPAC-7186PEG
Power Supply
Power Requirements
+10 ~ +30 V DC (unregulated)
+12 ~ +48 V DC (unregulated)
Protection
Power reverse polarity protection
PoE
No
IEEE 802.3af, Class 1
Power Consumption
1.5 W for μPAC-7186EG/PEG
2.5 W for μPAC-7186EGD/PEGD (when I/O slots are empty)
General Environment
Temperature
Operating: -25 ~+75 °C,
Storage : -30 ~ +85 °C
Humidity
5 ~ 95% RH (non-condensing )
System
CPU
80186 or compatible (16-bit and 80 MHz)
Watchdog Timer
Yes, default 0.8 second
RTC (Real Time Clock)
Provide seconds, minutes, hours, day of week/month, month and year, valid from 1980 to 2079
SRAM
640 KB
768 KB
FLASH Memory
512 KB, Erase unit is 64 KB, 100,000 erase/write cycles
NVRAM
31 bytes, battery backup, data valid up to 10 years
All Xxxx series DO boards support PWM output. 8-ch max. for one controller.
500 Hz max. for Off=1 & On=1 ms
Output square curve: Off: 1 ~ 32767 ms, On: 1 ~ 32767 ms
Counters
Parallel DI Counter
All Xxxx series DI boards support DI counter.
8-ch. max. for one controller. Counter value: 32-bit
500Hz max. Min. pulse width > 1 ms
Remote DI Counter
All remote I-7000 & I-87K DI modules support counters. 100 Hz max. value: 0 ~ 65535
Remote High Speed Counter
Optional I-87082:100 kHz max. ,32-bit
Protocols
Modbus Slave Protocol
Up to 2 COM Ports (COM1, one of COM2 or COM3-in-X-board) can support Modbus RTU Slave protocol for connecting ISaGRAF, PC/HMI/OPC Server & MMI panels.
Modbus Master Protocol
Up to 2 COM Ports (COM1 , COM2 and COM3-in-X-board) support Modbus RTU/ASCII Master protocol to connect to other Modbus Slave I/O devices
Modbus TCP/IP Protocol
Ethernet port supports Modbus TCP/IP Slave protocol for connecting ISaGRAF & PC/HMI.
Remote I/O
One of COM2 (or COM3:RS-485 if found) supports I-7000 I/O modules & (I-87K base + I-87K serial I/O boards or RU-87P1/2/4/8 + I-87K High Profile I/O cards) as Remote I/O. Max. 64 I/O module for one controller
Fbus
Built-in COM2 Port to exchange data between ICP DAS's ISaGRAF PACs.
Ebus
To exchange data between ICP DAS’s ISaGRAF Ethernet PACs via Ethernet port.
Send Email
Send email to maximum 10 receivers each time via internet. If applying with an X607/608 X-board, it could send email with one attached file and the maximum file size is about 488 KB for using X608 or about 112 KB for using X607.
SMS: Short Message Service
One of (COM1 or COM3:RS-232 or COM4:RS-232 if found) can link to a GSM modem to support SMS. User can request data/control the controller by cellular phone. The controller can also send data & alarms to user's cellular phone. Optional GSM modems: GTM-201-RS232 ( 850/900/1800/1900 GSM/GPRS External Modem)
User-defined Protocol
User can write his own protocol applied at COM1, COM2 & (COM3 ~ COM8 if found) by serial communication function blocks.
Modem Link
Supports PC to remotely download & monitor the controller through COM4 of X504.
MMICON/LCD
One of (COM3: RS-232 if found) supports ICP DAS's MMICON. The MMICON is featured with a 240 x 64 dot LCD and a 4 x 4 Keyboard. User can use it to display picture, string, integer, float, and input a character, string, integer and float.
Redundancy Solution
One is Master, one is Slave. Master handles all inputs & outputs at run time. If Master is damaged (or Power off), Slave takes the control of Bus7000b. If Master is alive from damaged (or power up again), it takes the control of Bus7000b again. The change over time is about 5 seconds. Control data is exchanging via Ebus (if using a cross cable, no need any Ethernet switch). All I/O should be RS-485 I/O except the status I/O in the slot 0: X-107.
CAN/CANopen
μPAC-7186EG can use its COM1 or COM3 to COM8 (resides at the X5xx RS-232 expansion board) to connect one I-7530 : the RS-232 to CAN converter to support CAN and CANopen devices and sensors. One μPAC-7186EG supports max.3 RS-232 port to connect max.3 I-7530. Please refer towww.icpdas.com > FAQ > Software > ISaGRAF Ver.3 (English) >086
Battery Backup SRAM
With the optional X607 or X608 board plugged inside the μPAC-7186EG/PEG, data can be stored in it, and then PC can load these data via COM1 or Ethernet. PC can also download pre-defined data to X607/608. Optional: X607: 128 KB, X608: 512 KB