I-7530

 

Tabelka poniżej prezentuje parametry techniczne urządzenia. W przypadku, gdyby prezentowane w niej informacje były niekompletne lub budziły wątpliwości prosimy o kontakt mailem bądź telefonicznie z naszym działem technicznym. Dodatkowo służymy pomocą w doborze właściwego urządzenia tak, aby optymalnie spełniało wymagania Państwa projektu.

Features

Microprocessor inside with 20MHz CAN interface connector: D-Sub 9-pin 82C250 CAN transceiver Built-in CAN/RS-232 Converter firmware Max transmission speed up to 1M bps for CAN and 115.2K bps for RS-232 Software configurable CAN and RS-232 communication parameters Max transmission distance over 1000m (follow CAN specification) Support both CAN 2.0A and CAN 2.0B Build-in jumper to select 120 ohm terminal resister Mount easily on DIN-rail Power, data flow and error indicator for CAN and RS-232 Watchdog inside Support transparent communication mode Provide a group of RS-232 devices a method to be the network system (duplex communication mode of RS-232 devices is not supported)

Applications

Control System Building Automation Factory Automation Distributed data acquisition

I-7530 Software Utility Features

CAN bus Baud rate configuration CAN acceptance filter configuration CAN 2.0A or 2.0B specific selection RS-232 Baud rate and data bit setting RS-232 responded selection Easy test to transmit/receive can messages Setting for I-7530 communication mode (normal mode or pair connection mode)

Hardware Specifications

RS-232 interface connector: D-Sub 9-pin CAN interface connector: D-Sub 9-pin Isolation voltage: 3000Vrms on the CAN side Repeater request: over than 1000m (suggestion) Accessories: One D-Sub 9-pin cable Dimensions: 123mm x 72mm x 33mm Power requirement: Unregulated 10~30 Vdc with protection from power reversals Power consumption: 1W Operating temperature: -25℃ to +75℃ Storage temperature: -40℃ to +80℃ Communication speed: 115.2K bps max for RS-232 1M bps max for CAN

Product specification
Hardware
EEPROM	2 KB (for system information), 100,000 erase/write cycles
CAN Interface
Transceiver	NXP 82C250
Channel number	1
Connector	9-pin male D-Sub (CAN_L, CAN_H, N/A for others)
Baud Rate (bps)	10 k, 20 k, 50 k, 125 k, 250 k, 500 k, 800 k, 1 Mbps
Isolation	3000 VDC for DC-to-DC, 2500 Vrms for photo-couple
Terminator Resistor	Selectable 120 terminator resistor by jumper
Specification	ISO-11898-2, CAN 2.0A and CAN 2.0B
Receive Buffer	1000 data frames
RS-232 Interface
Connector	9-pin female D-Sub (TxD, RxD, GND, N/A for others )
Baud Rate (bps)	110, 150, 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200bps
Data bit	5, 6, 7, 8
Stop bit	1, 2
Parity bit	None, Even, Odd
Receive Buffer	900 data frames
LED
Round LED	ON LED: Power and Data Flow ERR LED: Error Status
Power
Protection	Power reverse polarity protection, Over-voltage brown-out protection
Power Consumption	1 W
Mechanism
Installation	DIN-Rail
Dimensions	72mm x 118mm x 33mm (W x L x H)
Environment
Operating Temp.	-25 ~ 75 C
Storage Temp.	-30 ~ 80 C
Humidity	10 ~ 90% RH, non-condensing

Cechy produktu:
Konwerter
Konwertery
Typ urządzenia ZigBee
Producent	ICPDAS
Cechy urządzenia	Programowalny
Porty szeregowe	RS-232
Interfejsy	CAN
I/O	Wejścia izolowane
Typ konwertera	Konwerter programowalny